Penicillium oxalicum induced phosphate precipitation enhanced cadmium (Cd) immobilization by simultaneously accelerating Cd biosorption and biomineralization.

Soil cadmium (Cd) is immobilized by the progressing biomineralization process as microbial induced phosphate precipitation (MIPP), which is regulated by phosphate (P) solubilizing microorganisms and P sources. However, little attention has been paid to the implications of Cd biosorption during MIPP. In this study, the newly isolated Penicillium oxalicum could immobilize 5.4-12.6 % of Cd2+, while the presence of hydroxyapatite (HAP) considerably enhanced Cd2+ immobilization in P. oxalicum and reached over 99 % Cd2+ immobilization efficiency within 7 days. Compared to P. oxalicum mono inoculation, MIPP dramatically boosted Cd biosorption and biomineralization efficiency by 71 % and 16 % after 96 h cultivation, respectively. P. oxalicum preferred to absorbing Cd2+ and reaching maximum Cd2+ biosorption efficiency of 87.8 % in the presence of HAP. More surface groups in P. oxalicum and HAP mineral involved adsorption which resulted in the formation of Cd-apatite [Ca8Cd2(PO4)6(OH)2] via ion exchange. Intracellular S2-, secreted organic acids and soluble P via HAP solubilization complexed with Cd2+, progressively mineralized into Cd5(PO4)3OH, Cd(H2PO4)2, C4H6CdO4 and CdS. These results suggested that Cd2+ immobilization was enhanced simultaneously by the accelerated biosorption and biomineralization during P. oxalicum induced P precipitation. Our findings revealed new mechanisms of Cd immobilization in MIPP process and offered clues for remediation practices at metal contaminated sites.

Microbial-induced carbonate precipitation effectively prevents Pb2+ migration through the soil profile: Lab experiment and model simulation.

Due to the inappropriate disposal of waste materials containing lead (Pb) and irrigation with sewage containing Pb, the migration of Pb2+ within the soil profile has been extensively investigated. The conventional Pb2+ block method is challenging to implement due to its complex operational procedures and high construction costs. To address this issue, this study introduces the microbial-induced carbonate precipitation (MICP) technique as a novel approach to impede the migration of Pb2+ in the soil profile. Soil acclimatization with urea resulted in an increased proportion of urease-producing microorganisms, including Bacillus, Paenibacillus, and Planococcaceae, along with heightened expression of urea-hydrolyzing genes (UreA, UreB, UreC, and UreG). This indicates that urea-acclimatized soil (Soil-MICP) possesses the potential to induce carbonate precipitation. Batch Pb2+ fixation experiments confirmed that the fixation efficiency of Soil-MICP on Pb2+ exceeded that of soil without MICP, attributed to the MICP process within the Soil-MICP group. Dynamic migration experiments revealed that the MICP reaction transformed exchangeable lead into carbonate-bound Pb, effectively impeding Pb2+ migration in the soil profile. Additionally, the migration rate of Pb2+ in Soil-MICP was influenced by varying urea amounts, pH levels, and pore flow rates, leading to a slowdown in migration. The Two-site sorption model aptly described the Pb2+ migration process in the Soil-MICP column. This study aims to elucidate the MICP biomineralization process, uncover the in-situ blocking mechanism of MICP on lead in soil, investigate the impact of Pb on key genes involved in urease metabolism, enhance the comprehension of the chemical morphology of lead mineralization products, and provide a theoretical foundation for MICP technology in preventing the migration of Pb2+ in soil profiles.

Optimization of culture medium to improve bio-cementation effect based on response surface method.

The main challenge in the large-scale application of MICP lies in its low efficiency and promoting biofilm growth can effectively address this problem. In the present study, a prediction model was proposed using the response surface method. With the prediction model, optimum concentrations of nutrients in the medium can be obtained. Moreover, the optimized medium was compared with other media via bio-cementation tests. The results show that this prediction model was accurate and effective, and the predicted results were close to the measured results. By using the prediction model, the optimized culture media was determined (20.0 g/l yeast extract, 10.0 g/l polypeptone, 5.0 g/l ammonium sulfate, and 10.0 g/l NaCl). Furthermore, the optimized medium significantly promoted the growth of biofilm compared to other media. In the medium, the effect of polypeptone on biofilm growth was smaller than the effect of yeast extract and increasing the concentration of polypeptone was not beneficial in promoting biofilm growth. In addition, the sand column solidified with the optimized medium had the highest strength and the largest calcium carbonate contents. The prediction model represents a platform technology that leverages culture medium to impart novel sensing, adjustive, and responsive multifunctionality to structural materials in the civil engineering and material engineering fields.

Antisolvent precipitation for the synergistic preparation of ultrafine particles of nobiletin under ultrasonication-homogenization and evaluation of the inhibitory effects of α-glucosidase and porcine pancreatic lipase in vitro.

To further enhance the application of nobiletin (an important active ingredient in Citrus fruits), we used ultrasonic homogenization-assisted antisolvent precipitation to create ultrafine particles of nobiletin (UPN). DMSO was used as the solvent, and deionized water was used as the antisolvent. When ultrasonication (670 W) and homogenization (16000 r/min) were synergistic, the solution concentration was 57 mg/mL, and the minimum particle size of UPN was 521.02 nm. The UPN samples outperformed the RN samples in terms of the inhibition of porcine pancreatic lipase, which was inhibited (by 500 mg/mL) by 68.41 % in the raw sample, 90.34 % in the ultrafine sample, and 83.59 % in the positive control, according to the data. Fourier transform infrared spectroscopy analysis revealed no chemical changes in the samples before or after preparation. However, the crystallinity of the processed ultrafine nobiletin particles decreased. Thus, this work offers significant relevance for applications in the realm of food chemistry and indirectly illustrates the expanded application potential of nobiletin.

Statistical modelling, optimization, and mechanistic exploration of novel ureolytic Enterobacter hormaechei IITISM-SA3 in cadmium immobilization under microbial inclusive and cell-free conditions through microbially induced calcite precipitation.

The study aimed to evaluate the potential of a novel isolated ureolytic Enterobacter hormaechei IITISM-SA3 in cadmium bioremoval through MICP. The optimization and modelling of the biotic and abiotic factors affecting the process of mineralization were also performed. In addition, the underlying mechanism of MICP-driven Cd mineralization under microbial-inclusive and cell-free conditions was revealed and supported through the characterization of the bio-precipitates obtained using various characterization techniques. The results indicated that the isolate could remove 97.18% Cd2+ of 11.4 ppm under optimized conditions of 36.86 h, pH 7.63, and biomass dose of 1.75 ml. Besides, the presence and absence of bacterial cells were found to influence both the morphologies and crystalline structures of precipitates. The precipitates obtained under microbial-inclusive conditions showed typical rhombohedral crystalline structures of the composition comprising CaCO3, CdCO3, and 0.67Ca0.33CdCO3. However, the crystalline nature of the precipitate reduced to a nano-sized granular structure in cell-free media. Unlike the cadmium mineralization process under microbial-inclusive media, where bacterial cells serve as nucleation sites for crystallization, the carbonate precipitation effectively captures Cd2+ through co-precipitation, chemisorption, or alternative mechanisms involving interactions between metal ions and CaCO3 under cell-free conditions. The findings presented suggest that using cell-free culture supernatant enriched with carbonate ions provides an avenue that could be harnessed for sustainable metal remediation.

Interaction of microorganisms with carbonates from the micro to the macro scales during sedimentation: Insights into the early stage of biodegradation.

The assembly process of Organic Matter (OM) from single molecules to polymers and the formation process of Ca-CO3 ion-pairs are explored at the micro-scale, and then the relationship between OM and carbonate based on the results of microbially-induced carbonate precipitation (MICP) laboratory experiments is established at the macro-scale. Molecular dynamics (MD) is used to model the assembly of OM (a) in an aqueous solution, (b) on surfaces of calcite (10 1‾ 4) crystals and (c) on defective calcite (101‾ 4) crystal surfaces. From the MICP experiments, carbonate minerals containing abundant OM were precipitated and were characterized by Scanning Electron Microscopy (SEM), X-Ray Diffractometry (XRD) and Fourier Transform Infrared Spectroscopy (FTIR). The results of the MD show that OM is assembled into polymers in all three simulation systems. Although the Ca-CO3 ion-pairs and OM were briefly combined, the aggregation assembly of OM molecules and the precipitation of carbonate calcium are not related in the long run. The highly specific surface area of the defective calcite shows an increase in the adsorption of OM. The van der Waals forces, which are primarily responsible for controlling the assembly of OM molecules, increase with the degree of aggregation. According to the MICP experiments, OM is enriched on the mineral surfaces, and more OM is found at the steps of defective crystals with their larger surface areas. Through MD and MICP laboratory experiments, this work systematically describes the interaction of OM and carbonate minerals from the micro to the macro scales, and this provides insight into the interaction between OM and carbonates and biogeochemical processes related to the accumulation of OM in sediments.

Identification and extraction of cementation patterns in sand modified by MICP: New insights at the pore scale.

Microbially induced calcium carbonate precipitation (MICP) is an environmentally friendly technology that improves soil permeability resistance through biocementation. In this study, 2D microscopic analysis and 3D volume reconstruction were performed on river sand after 24 cycles of bio-treatment based on stacked images and computed tomography (CT) scanning data, respectively, to extract biocementation patterns between particles. Based on the mutual validation findings of the two techniques, three patterns in the biocemented sand were identified as G-C-G, G-C, and G-G. Specifically, 2D microscopic analysis showed that G-C-G featured multi-particle encapsulation and bridging, with a pore filling ratio of 81.2%; G-C was characterized by locally coated particle layers, with a pore filling ratio of 19.7%; and the G-G was marked by sporadic filling of interparticle pores, with a pore filling ratio of 11.7%. G-C-G had the best cementation effect and permeability resistance (effective sealing rate of 68.5%), whereas G-C (effective sealing rate of 2.4%) had a relatively minor contribution to pore-filling and flow sealing. 3D volume reconstruction showed that G-C-G had the highest pore filling rate, followed by G-G and G-C. The average filling ratios of area and volume for G-C-G were 83.979% and 77.257%, respectively; for G-G 20.360% and 23.600%; and for G-C 11.545% and 11.250%. The analysis of the representative element volume (REV) was conducted, and the feasibility and reliability of the micro-scale pattern extraction results were confirmed to guide the analysis of macro-scale characteristics. The exploration of the effectiveness of cementation patterns in fluid sealing provides valuable insights into effective biocementation at the pore scale of porous media, which may inspire future research.

Enhanced nutrient recovery from anaerobically digested poultry wastewater through struvite precipitation by organic acid pre-treatment and seeding in a bubble column electrolytic reactor.

Limited mineralization of organic phosphorus to phosphate during the anaerobic digestion process poses a significant challenge in the development of cost-effective nutrient recovery strategies from anaerobically digested poultry wastewater (ADPW). This study investigated the influence of organic acids on phosphorus solubilization from ADPW, followed by its recycling in the form of struvite using a bubble column electrolytic reactor (BCER) without adding chemicals. The impact of seeding on the efficiency of PO43- and NH3-N recovery as well as the size distribution of recovered precipitates from the acid pre-treated ADPW was also evaluated. Pre-treatment of the ADPW with oxalic acid achieved complete solubilization of phosphorus, reaching ∼100% extraction efficiency at pH 2.5. The maximum removal efficiency of phosphate and ammonia-nitrogen from the ADPW were 88.9% and 90.1%, respectively, while the addition of 5 and 10 g/L struvite seed to the BCER increased PO43- removal efficiency by 9.6% and 11.5%, respectively. The value of the kinetic rate constant, k, increased from 0.0176 min-1 (unseeded) to 0.0198 min-1, 0.0307 min-1, and 0.0375 min-1 with the seed loading rate of 2, 5, and 10 g/L, respectively. Concurrently, the average particle size rose from 75.3 µm (unseeded) to 82.1 µm, 125.7 µm, and 148.9 µm, respectively. Results from XRD, FTIR, EDS, and dissolved chemical analysis revealed that the solid product obtained from the recovery process was a multi-nutrient fertilizer consisting of 94.7% struvite with negligible levels of heavy metals.

Biotrapping Ureolytic Bacteria on Sand to Improve the Efficiency of Biocementation.

Microbially induced calcium carbonate precipitation (MICP) has emerged as a novel technology with the potential to produce building materials through lower-temperature processes. The formation of calcium carbonate bridges in MICP allows the biocementation of aggregate particles to produce biobricks. Current approaches require several pulses of microbes and mineralization media to increase the quantity of calcium carbonate minerals and improve the strength of the material, thus leading to a reduction in sustainability. One potential technique to improve the efficiency of strength development involves trapping the bacteria on the aggregate surfaces using silane coupling agents such as positively charged 3-aminopropyl-methyl-diethoxysilane (APMDES). This treatment traps bacteria on sand through electrostatic interactions that attract negatively charged walls of bacteria to positively charged amine groups. The APMDES treatment promoted an abundant and immediate association of bacteria with sand, increasing the spatial density of ureolytic microbes on sand and promoting efficient initial calcium carbonate precipitation. Though microbial viability was compromised by treatment, urea hydrolysis was minimally affected. Strength was gained much more rapidly for the APMDES-treated sand than for the untreated sand. Three injections of bacteria and biomineralization media using APMDES-treated sand led to the same strength gain as seven injections using untreated sand. The higher strength with APMDES treatment was not explained by increased calcium carbonate accrual in the structure and may be influenced by additional factors such as differences in the microstructure of calcium carbonate bridges between sand particles. Overall, incorporating pretreatment methods, such as amine silane coupling agents, opens a new avenue in biomineralization research by producing materials with an improved efficiency and sustainability.

Uncovering the Dynamics of Urease and Carbonic Anhydrase Genes in Ureolysis, Carbon Dioxide Hydration, and Calcium Carbonate Precipitation.

The hydration of CO2 suffers from kinetic inefficiencies that make its natural trapping impractically sluggish. However, CO2-fixing carbonic anhydrases (CAs) remarkably accelerate its equilibration by 6 orders of magnitude and are, therefore, "ideal" catalysts. Notably, CA has been detected in ureolytic bacteria, suggesting its potential involvement in microbially induced carbonate precipitation (MICP), yet the dynamics of the urease (Ur) and CA genes remain poorly understood. Here, through the use of the ureolytic bacteriumSporosarcina pasteurii, we investigate the differing role of Ur and CA in ureolysis, CO2 hydration, and CaCO3 precipitation with increasing CO2(g) concentrations. We show that Ur gene up-regulation coincides with an increase in [HCO3-] following the hydration of CO2 to HCO3- by CA. Hence, CA physiologically promotes buffering, which enhances solubility trapping and affects the phase of the CaCO3 mineral formed. Understanding the role of CO2 hydration on the performance of ureolysis and CaCO3 precipitation provides essential new insights, required for the development of next-generation biocatalyzed CO2 trapping technologies.

A numerical model of the MICP multi-process considering the scale size.

As an environmentally friendly and controllable technology, Microbially induced carbonate precipitation (MICP) has broad applications in geotechnical and environmental fields. However, the longitudinal dispersivity in MICP multi-process varies with the scale size. Ignoring the effect of the scale size of the research object on the dispersivity leads to the inaccuracy between the numerical model and the experiment data. Thus, this paper has established the relationship between the scale size and the dispersivity initially, and optimized the theoretical system of MICP multi-process reaction. When scale size increases logarithmically from 10-2 m to 105 m, longitudinal dispersivity shows a trend of increasing from 10-3 m to 104 m. The distribution of calcium carbonate is closer to the experimentally measured value when the size effect is considered. After considering the scale size, the suspended bacteria and attached bacteria are higher than the cased without considering the size effect, which leads to a higher calcium carbonate content. Scale has little effect on the penetration law of the suspended bacteria. The maximum carbonate content increases with the increase of the initial porosity, and the average carbonate shows a significant increasing trend with the increase of the bacterial injecting rate. In the simulation of the microbial mineralization kinetic model, it is recommended to consider the influence of the scale size on the MICP multi-process.

A holistic approach to the recovery of valuable substances from the treatment sludge formed from chemical precipitation of fruit processing industry wastewater.

In this study, recovery of phenolic substances with Soxhlet extraction, (SE) ultrasound-assisted extraction (UAS), and supercritical CO2 (SC-CO2) extraction methods from chemical sludge obtained with chemical precipitation (FeCl3/PACS, Ca(OH)2/PACS, perlite/PACS, FeCl3/cationic polyelectrolyte) of lemon processing wastewater was investigated. The effect of used coagulants/flocculants and pH on COD and total phenolic substance content (TPC) removal was researched. Recovered phenolic substance profiles were also determined with HPLC-DAD. Additionally, response surface methodology was used to determine optimum treatment conditions. ANOVA analysis showed that pH is a more important variable than coagulant/flocculant doses for all chemical precipitation experimental sets. The highest removal efficiencies for COD and TPC was obtained in FeCl3/PACS (COD: 72.0 %, TPC: 93.7 %). Optimum dose values were determined as pH: 4, FeCl3: 3000 mg/L, PACS: 400 mg/L for FeCl3/PACS, pH: 6.5, Ca(OH)2: 1500 mg/L, PACS: 300 mg/L for Ca(OH)2/PACS, pH: 5.5, PACS: 7000 mg/L, perlite: 50 g/L for perlite/PACS, pH: 4.5, FeCl3: 500 mg/L, polyelectrolyte: 4 mg/L for FeCl3/polyelectrolyte. TPC removal efficiencies were determined as 55 %, 35 %, 57 % and 58 % in these conditions, respectively. Maximum TPC in extracts was determined as 39.03 mg GAE/g extract, 8.81 mg GAE/g extract, and 4.34 mg GAE/g extract for SE, UAS, and SC-CO2, respectively. TPC recovery efficiencies (RTPC) for all chemical sludge were SE > UAS > SC-CO2. Additionally, the TPC profile has shown a difference depending on the extraction method. According to the results of this study, it was concluded that the coagulation-flocculation process may be a suitable alternative for fruit juice processing industry wastewater in terms of both reducing environmental pollution and recovering polyphenolics from formed sludge. Consequently, this study presented a different perspective on the recovery from wastes with valuable substance recovery from chemical sludge.

Microbial induced carbonate precipitation for remediation of heavy metals, ions and radioactive elements: A comprehensive exploration of prospective applications in water and soil treatment.

Improper disposal practices have caused environmental disruptions, possessing by heavy metal ions and radioactive elements in water and soil, where the innovative and sustainable remediation strategies are significantly imperative in last few decades. Microbially induced carbonate precipitation (MICP) has emerged as a pioneering technology for remediating contaminated soil and water. Generally, MICP employs urease-producing microorganisms to decompose urea (NH2CONH2) into ammonium (NH4+and carbon dioxide (CO2), thereby increasing pH levels and inducing carbonate precipitation (CO32-), and effectively removing remove contaminants. Nonetheless, the intricate mechanism underlying heavy metal mineralization poses a significant challenge, constraining its application in contaminants engineering, particularly in the context of prolonged heavy metal leaching over time and its efficacy in adverse environmental conditions. This review provides a comprehensive idea of recent development of MICP and its application in environmental engineering, examining metabolic pathways, mineral precipitation mechanisms, and environmental factors as well as providing future perspectives for commercial utilization. The use of ureolytic bacteria in MICP demonstrates cost-efficiency, environmental compatibility, and successful pollutant abatement over tradition bioremediation techniques, and bio-synthesis of nanoparticles. limitations such as large-scale application, elevated Ca2+levels in groundwater, and gradual contaminant release need to be overcome. The possible future research directions for MICP technology, emphasizing its potential in conventional remediation, CO2 sequestration, bio-material synthesis, and its role in reducing environmental impact for long-term economic benefits.

Enrichment, characterization, and sand consolidation application of urease active calcite-producing bacteria.

Minerals such as calcium carbonate, which is prevalent in marble and limestone, are present naturally in rocks. Both physicochemical processes and microbial processes can result in the creation of calcium carbonate in nature, as is well documented. In this study, microbiologically induced calcite precipitation potential of three different Travertine-type water sources (Pamukkale Travertine Spring (PTS), Pamukkale Travertine Terraces (PTT), and Red Travertine of Karahayit (RTK)) using three different incubation media (NB, NB3, and ATCC1832) were investigated. After enrichment with ATCC1832 media, urease assays were positive for all of the microbial sources. The PTS and PTT were cultured with ATCC1832 medium for 48 h, which showed the best results for urease activity and microbial growth among other samples. Metagenome analyses indicated that PTT enriched with ATCC1832 media contains > 99% Firmicutes, while PTS enriched with ATCC1832 contains > 99% Proteobacteria at the Phylum level. Results from SEM-EDX and XRD analysis revealed that calcite and/or vaterite were the minerals that emerged from the mineralization of the PTS and PTT during incubation. The type of calcium carbonate crystals tended to change from one form to another when the incubation period extends from 72 to 120 h. Both the PTS and the PTT were able to precipitate calcite within the sand column. However, the bacteria from the PTT (26% CaCO3) outperformed those from the PTS (18% CaCO3) in terms of calcium carbonate deposition on the 21st day of incubation.

Immobilization of Cd2+ in an aqueous environment using a two-step microbial-induced carbonate precipitation method.

Previous researches indicate that the potent toxicity of cadmium hinders the efficacy of the microbial-induced carbonate precipitation (MICP) process for bioremediation of Cd2+ in aqueous environment. Increasing urea and calcium resource doses, introducing synergists, and utilizing urease-producing consortia can improve bio-immobilization performance of MICP. However, such measures may incur cost increases and/or secondary contamination. This study first verifies the substantial biotoxicity of Cd2+ for urease activity and then analyzes the practical limitation of traditional MICP using Bacillus pasteurii for bioremediation of Cd2+ in an aqueous environment containing 1-40 mM Cd2+ by a series tube tests and numerical simulation. Subsequently, a two-step MICP method, which separates urea hydrolysis and heavy metal precipitation, is introduced in this study to eliminate the inhibitory effect of heavy metal on urease activity. The concentrations of ammonium, Cd2+, and pH were monitored over time. The results indicate that the urease expression in B. pasteurii can be significantly inhibited by Cd2+ particularly at the concentration ranging from 10 to 40 mM, leading to pretty low efficacy of traditional MICP for bioremediation of Cd2+ (Cd2+ removal rate as low as 21.55-38.47% when the initial Cd2+ concentration = 40 mM). In contrast, when the two-step MICP method is applied, the Cd2+ can be almost completely immobilized, even though the concentration ratio of urea to Cd2+ is as low as 1.5:1.0, which is close to the theory minimum concentration ratio for the complete precipitation of carbonate to cadmium ions(1.0:1.0). Therefore, the cost-effective, environmentally sustainable, and straightforward two-step MICP method holds great potential for application in the bioremediation of Cd2+-contaminated solutions in high concentration.

Investigation into struvite precipitation: A commonly encountered problem during fermentations on chemically defined media.

Chemically defined mineral media are widely used in bioprocesses, as these show less batch to batch variation compared with complex media. Nonetheless, the recommended media formulations often lead to the formation of precipitants at elevated pH values. These precipitates are insoluble and reduce the availability of macronutrients to the cells, which can result in limiting growth rates and lower productivity. They can also damage equipment by clogging pipes, hoses, and spargers in stirred tank fermenters. In this study, the observed precipitate was analyzed via X-ray fluorescence spectroscopy and identified as the magnesium ammonium phosphate salt struvite (MgNH4 PO4 × 6H2 O). The solubility of struvite crystals is known to be extremely low, causing the macronutrients magnesium, phosphate, and ammonium to be bound in the struvite crystals. Here, it was shown that struvite precipitates can be redissolved under common fermentation conditions. Furthermore, it was found that the struvite particle size distribution has a significant effect on the dissolution kinetics, which directly affects macronutrient availability. At a certain particle size, struvite crystals rapidly dissolved and provided unlimiting growth conditions. Therefore, struvite formation should be considered during media and bioprocess development, to ensure that the dissolution kinetics of struvite are faster than the growth kinetics.

Co-precipitation of Cd with struvite during phosphorus recovery.

During the struvite recovery process, Cd, a hazardous metal commonly found in waste streams, can be sequestered by struvite. This study investigated the influence of Cd2+ on the precipitation of struvite. Quantitative X-ray diffraction (QXRD) results showed that the purity of struvite decreased from 99.1% to 73.6% as Cd concentration increased from 1 to 500 µM. Scanning electron microscopy (SEM) revealed a roughened surface of struvite, and X-ray photoelectron spectroscopy (XPS) analysis indicated that the peak area ratio of Cd-OH increased from 19.4% to 51.3%, while the area ratio of Cd-PO4 decreased from 86.6% to 48.7% as Cd concentrations increased from 10 to 500 µM. The findings suggested that Cd2+ disrupted the crystal growth of struvite, and mainly combined with -OH and -PO4 to form amorphous Cd-bearing compounds co-precipitated with struvite. Additionally, Mg-containing amorphous phases were formed by incorporating Mg2+ with -OH and -PO4 during struvite formation.

Effect of (in)organic additives on microbially induced calcium carbonate precipitation.

AIM: This study aimed to understand the morphological effects of (in)organic additives on microbially induced calcium carbonate precipitation (MICP). METHODS AND RESULTS: MICP was monitored in real time in the presence of (in)organic additives: bovine serum albumin (BSA), biofilm surface layer protein A (BslA), magnesium chloride (MgCl2), and poly-l-lysine. This monitoring was carried out using confocal microscopy to observe the formation of CaCO3 from the point of nucleation, in comparison to conditions without additives. Complementary methodologies, namely scanning electron microscopy, energy-dispersive X-ray spectroscopy and X-ray diffraction, were employed to assess the visual morphology, elemental composition, and crystalline structures of CaCO3, respectively, following the crystals' formation. The results demonstrated that in the presence of additives, more CaCO3 crystals were produced at 100 min compared to the reaction without additives. The inclusion of BslA resulted in larger crystals than reactions containing other additives, including MgCl2. BSA induced a significant number of crystals from the early stages of the reaction (20 min) but did not have a substantial impact on crystal size compared to conditions without additives. All additives led to a higher content of calcite compared to vaterite after a 24-h reaction, with the exception of MgCl2, which produced a substantial quantity of magnesium calcite. CONCLUSIONS: The work demonstrates the effect of several (in)organic additives on MICP and sets the stage for further research to understand additive effects on MICP to achieve controlled CaCO3 precipitation.

Comparative study of hydroxyapatite synthesized using Schiff base and wet chemical precipitation methods.

Hydroxyapatite (HAp) exists as an inorganic and crystalline composition present in bones and dental enamel, and hence can be utilized as a direct element or as part of the composition of biomaterials and implants for dental and orthopaedic applications. Listed below are a few synthesis techniques for HAp that are listed in the literature: solid-state and mechano-chemical methods (dry methods), wet chemical precipitation and sol-gel methods (wet methods), and combustion and pyrolysis methods (high-temperature processes). Nevertheless, there are new and more productive techniques that result in HAp with a regulated morphology, such as the Schiff base method, which, on reaction with calcium and phosphate precursors, forms chelating complexes to produce HAp nuclei. This research paper presents the comparison in characteristics between HAp synthesized using Schiff base (HAp-SB), wet chemical precipitation (HAp-WC) methods, and commercial HAp (HAp-CM) in their powdered and pelleted form. The average size of HAp-WC particles in the spherical form was found to be 603 nm ± 176, HAp-SB were found to have rod-like morphology, which is very similar to human bone-like HAp, with an average length and width of 1522 nm ± 759 and 400 nm ± 112, respectively, and HAp-CM were found to have spherical morphology with dimensions of 52 nm ± 25. Biological studies show that cell viability of HAp-SB pellet (202.01% ± 8.16) seemed to have higher cell proliferation properties than HAp-WC pellet (145.7% ± 5.11) and HAp-CM pellet (71.53% ± 3.61) due to its higher aspect ratio, and hence higher surface area for the cells to adhere. In a detailed study, it is observed that both techniques had their advantages, and there were no significant disadvantages observed.

Self-assembled silk fibroin cross-linked with genipin supplements microbial carbonate precipitation in building material.

The process of microbially induced carbonate precipitation (MICP) is known to effectively improve engineering properties of building materials and so does silk fibroin (SF). Thus, in this study, an attempt was taken to see the improvement in sand, that is, basic building material coupled with MICP and SF. Urease producing Bacillus megaterium was utilized for MICP in Nutri-Calci medium. To improve the strength of SF itself in bacterial solution, it was cross-linked with genipin at the optimized concentration of 3.12 mg/mL. The Fourier transform infrared (FTIR) spectra confirmed the crosslinking of SF with genipin in bacterial solution. In order to understand how such cross-linking can improve engineering properties, sand moulds of 50 mm3 dimension were prepared that resulted in 35% and 55% more compressive strength than the one prepared with bacterial solution with SF and bacterial solution only, respectively with higher calcite content in former one. The FTIR, SEM, x-ray powder diffraction spectrometry and x-ray photoelectron spectroscopy analyses confirmed higher biomineral precipitation in bacterial solution coupled with genipin cross-linked SF. As the process of MICP is proven to replace cement partially from concrete without negatively influence mechanical properties, SF cross-linked with genipin can provide additional significance in developing low-carbon cement-based composites.